How to choose a parking barrier starts with five questions: how wide is the lane, how many cars pass per hour, how will you stop the boom coming down on a car, how will the barrier open, and what happens in a power cut. The answers decide the barrier, the boom and the accessories together, because in most cases the barrier is sold as the body only. This guide answers them with figures from the Italian BFT barriers Misbar stocks, and gives you 3 ready setups for a residential compound, a tower and a warehouse.

Quick pick: which barrier for which entrance?

In short: a normal 3 m entrance with moderate traffic needs only the MOOVI 30. A wide entrance up to 6 m takes the MOOVI 60. An entrance where cars queue at peak times calls for the GIOTTO ULTRA 36, which is faster and runs on a 24 V motor.

Step 1: Measure the lane and choose the boom

Lane width sets the boom length, and boom length sets the barrier. The boom and its mounting kit are ordered separately from the barrier body:

Measure the actual width between the lane edges, not the whole road. If the lane falls between 3 and 5 m, choose a barrier that takes a boom longer than you need, never shorter.

Step 2: Estimate traffic and opening speed

At a residential compound, cars come and go at a steady pace through the day. At an office tower, mall or hospital, cars queue at the barrier during peak hours, and every second of opening time lengthens the line.

• MOOVI: a 230 V motor that BFT rates for semi-intensive use. The MOOVI 60 raises its long boom in 8 seconds, with adjustable slowdown at the end of travel.
• GIOTTO ULTRA 36: a 24 V motor that opens in 2.2 seconds with a boom up to 4 m, and 4 seconds with a boom up to 6 m on the XL version. An encoder tracks boom movement and reverses it on impact, and the built-in control board supports U-Link.

The rule of thumb: if the entrance sees daily queues, pay the difference for the GIOTTO. If traffic is moderate, the MOOVI is enough and saves you money.

[cta:69061443]

Step 3: Mind the heat and the install spot

BFT rates the MOOVI for -20 to +50°C with IP24 protection. In a Saudi summer, metal in direct sun can run hotter than the air, so if the entrance is fully exposed, consider a canopy over the barrier. Fix the body on a level concrete base and leave space around it to open the cover for service.

Before pouring the base, lay cable conduits from the barrier to the power source and to the photocell position on the far side of the lane. Skip this and you will be cutting asphalt later. If you plan to add a loop detector or a plate recognition camera in the future, lay a spare conduit now.

Step 4: Safety: photocells, flashers and boom lights

The most dangerous moment is the boom coming down on a car that is still passing. An installation isn't complete without protection:

• Photocell: the COMPACTA A20-180 is an infrared transmitter and receiver pair with a 20 m range. If a car breaks the beam, the boom won't lower. The head swivels 90° each way and fits MOOVI and GIOTTO barriers with the P903031 bracket, ordered separately.
• Loop detector: a wire loop buried in the asphalt under the boom senses the metal car above it, keeping the boom raised until the car clears. It complements the photocell rather than replacing it.
• Flasher: the RADIUS LED AC A R1 is a 230 V LED light with IP44 protection that warns drivers and pedestrians the boom is moving. It has a built-in 433.92 MHz receiver antenna.
• Boom lights: the MOOVI LIGHT 1 kit for 5 to 6 m booms, so drivers see the boom in dark car parks.

[cta:1474468946]

Step 5: How will the barrier open?

Who uses the entrance decides how it opens. Residents and regular staff suit a remote or a card, subscribers at a tower or mall car park suit plate recognition, and visitors need a guard or an intercom. Most entrances combine two methods or more.

• Remote: the MITTO COOL C2 has two buttons, 433 MHz and rolling code that is hard to clone, with 50 to 100 m range. Suits residents and the guard.
• Card reader or intercom: sends an open command to the barrier board. Check before buying that the device output matches the control board input.
• Plate recognition camera: the Uniview PKC2640@Z28-P is a 4MP camera with a 2.8 to 12 mm lens built for car park entrances. It detects vehicles by video and reads plates at up to 30 km/h, so the barrier opens for registered cars without stopping. Confirm with us that it supports the Saudi plate format before ordering.

Step 6: What happens in a power cut?

The MOOVI has a mechanical lock and a personal release key, so the guard can lift the boom by hand during an outage and lock it again afterwards. For entrances that can't afford downtime, ask us about a backup battery kit compatible with the barrier you choose.

3 ready setups

[cta:244149824]

For bigger entrances: MAXIMA ULTRA

Misbar also stocks the MAXIMA ULTRA 36, 36XL and 68 SM barriers with their accessories, such as the 4 m BOOM PS40 and its LIGHT PS/ES 40-IP67 lighting for the MAXIMA ULTRA 36. If your entrance doesn't suit the MOOVI or GIOTTO, send us the lane width and daily car count and we will recommend the right version.

4 common mistakes when buying a parking barrier

1. Buying the barrier body alone: the boom, mounting kit and photocell are ordered separately. Plan for them from the start so installation isn't delayed.
2. A boom shorter than the lane: it leaves a gap for a car or motorbike to slip through. Measure the real width.
3. A slow barrier at a busy entrance: 8 seconds to open is fine at a warehouse but builds a queue at a mall exit.
4. Installing without a photocell: the first car the boom hits will cost more than the photocell.

Buy your parking barrier from Misbar Alhasibat

Misbar stocks BFT parking barriers in the MOOVI, GIOTTO and MAXIMA ULTRA series, along with booms, mounting kits, photocells, flashers, remotes and boom lights, plus Uniview plate recognition cameras. Browse every BFT product on the brand page.

Prices on the store are final and include VAT, and you can split the payment with Tabby. Send us the lane width, a photo of the entrance and your daily car count on WhatsApp, and we will put together the full list of barrier and accessories.

Browse all parking barriers at Misbar →

FAQ

How do I choose a parking barrier?

Measure the lane to set the boom length, estimate traffic to choose between the MOOVI for moderate use and the GIOTTO for heavy use, then add a photocell, a flasher and the opening method that suits you.

Does the boom come with the barrier?

No. BFT barriers are sold as the body only, and the boom and mounting kit are ordered by lane width, such as the AQ3 with OMEGA AQ for the MOOVI 30.

What is the difference between MOOVI and GIOTTO?

The MOOVI uses a 230 V motor for moderate traffic and covers up to 3 m (MOOVI 30) or 6 m (MOOVI 60). The GIOTTO ULTRA 36 uses a faster 24 V motor, opening in 2.2 seconds with a boom up to 4 m, and its encoder reverses the boom on impact.

How do I open the barrier in a power cut?

On the MOOVI, release the mechanical lock with the personal key and lift the boom by hand.

Can the barrier open by reading number plates?

Yes, with a plate recognition camera such as the PKC2640@Z28-P that reads the plate and opens for registered cars. Confirm with us that it works with the barrier's control board and the Saudi plate format.

Which barrier should you choose?

• Residential compound or villa with a 3 m entrance: the MOOVI 30 with an AQ3 boom.
• Wide entrance up to 6 m with moderate traffic: the MOOVI 60 with an ASTA 6MT boom.
• Tower, mall or hospital with heavy traffic: the GIOTTO ULTRA 36.
• For every barrier: a COMPACTA A20-180 photocell and a RADIUS LED flasher.

How to choose a PoE switch comes down to six questions: how many devices you will connect, how many watts they draw together, which PoE standard they need, what port speed, whether you need management, and how the switch connects to your recorder or router. A wrong switch rarely fails on install day; it fails weeks later when a camera starts rebooting at night. This guide answers all six with numbers and suggests a Uniview, Grandstream or Huawei switch for each case.

Quick pick: which PoE switch for which site?

Step 1: Count the ports

Count every device that will draw power from the switch: cameras, access points, IP phones and intercom units. Then add 20% spare ports for the camera or AP you will add later. A villa with 6 cameras and 2 access points needs 8 ports, and is better served by a switch with 8 PoE ports plus two extra uplinks than one with 8 ports in total.

Remember that uplink ports don't power anything. The NSW2010-10GT-POE-IN, for example, has 10 ports: 8 PoE plus 2 for the recorder and router.

Step 2: Work out the PoE power budget

The PoE budget is the total wattage the switch can share across all ports at once. Add up each device's maximum draw from its spec sheet, then add 25% headroom. Here are examples from devices Misbar stocks:

Villa example: 8 IPC3618LE cameras × 5.2 W = 41.6 W, plus one 21 W PTZ. That is 62.6 W, or 78 W with headroom. The 120 W NSW2010-10GT-POE-IN covers it, with a spare PoE port left over.

Office example: 12 cameras × 5.2 W = 62.4 W, plus 4 GWN7660E access points × 12.95 W = 51.8 W. That is 114.2 W, or 143 W with headroom, across 16 devices. Here you need the GWN7802P with 16 PoE ports and a 240 W budget.

Read the spec sheet closely: some switches can't give every port full power at once. The Huawei S210-8P2J, with a 128 W budget, runs all 8 ports at 15.4 W but only 4 ports at 30 W simultaneously.

[cta:1572542891]

Step 3: Match the PoE standard

• 802.3af (PoE): up to 15.4 W per port. Enough for most fixed cameras, small Wi-Fi 6 access points and IP phones.
• 802.3at (PoE+): up to 30 W per port. For PTZ cameras, high-density APs and Wi-Fi 7 units such as the GWN7670E.
• 802.3bt (PoE++): up to 60 W per port on the GWN7802P Pro. For the most power-hungry devices and room for future upgrades.

Every PoE+ switch also powers af devices, but not the other way round. If even one device needs at, buy a PoE+ switch.

Step 4: Port speed: 100 Mbps or gigabit?

A single camera stream is far below 100 Mbps, so a 10/100 port is enough for it. That is how the Uniview NSW2020 and NSW3000 switches are built, such as the NSW3000-24T1GT1GC-POE-IN with 24 PoE ports at 10/100 and two gigabit uplinks. All the camera traffic then travels over the gigabit port to the recorder.

Access points are different. They need at least gigabit ports, since Wi-Fi 6 speeds go well beyond 100 Mbps, and a Wi-Fi 7 AP with a 2.5G port only reaches full speed on a 2.5G switch port. So don't buy a 100 Mbps switch for a network with access points.

Step 5: Managed or unmanaged?

• Unmanaged: plug in and go. Enough for homes, villas and shops. The Uniview NSW2010 switches add a VLAN mode that isolates camera ports so they only talk to the uplinks, and an EXTEND mode that reaches up to 250 m for a distant camera.
• Cloud-managed: such as the NSW3000, which shows PoE draw per port, lets you turn a camera port off and on remotely, and discovers video devices to map the network.
• Managed L2+: such as the GWN7802P and GWN7803P. For companies that separate cameras, phones and guest Wi-Fi into VLANs and need Voice VLAN, QoS and IGMP snooping.

[cta:1821114803]

Step 6: Uplinks and SFP ports

Copper Ethernet reaches 100 m in normal mode. If the switch sits in one building and the router or recorder in another, use SFP ports with fibre. The GWN7802P has 4 × 1G SFP ports, the GWN7802P Pro 2 × 10G SFP+, and the Huawei S220-24P4X 4 × 10GE SFP+.

10G uplinks matter when a switch aggregates dozens of access points or links floors together, so the uplink doesn't become the bottleneck.

[cta:1095947608]

Suggested PoE switches by size

• 4 cameras: the NSW2010-5GT-POE-IN-UK, with 4 gigabit PoE ports, a 60 W budget and no fan.
• 8 cameras: the NSW2010-10GT-POE-IN, with a 120 W budget plus VLAN and EXTEND modes. If budget matters more than speed, the NSW2020-10T-POE-IN with 100 Mbps ports and 88 W.
• 8 devices including access points: the GWN7701PA with 8 PoE+ ports and 145 W, or the managed GWN7801P with two SFP ports.
• 16 cameras: the NSW3000-16T1GT1GC-POE-IN with a 250 W budget and cloud management.
• 24 cameras: the NSW3000-24T1GT1GC-POE-IN, or the gigabit NSW2010-26GT2GC-POE-IN, both with 370 W.
• Office with 24 devices: the GWN7803P with 370 W and 4 SFP ports, or the Huawei S220-24P4X with 400 W and 4 × 10G.

[cta:1938899985]

4 common mistakes when buying a PoE switch

1. A budget with no margin: a 60 W switch for devices drawing 58 W runs fine by day and drops a camera at night when the IR turns on. Leave 25%.
2. An af switch for a PTZ camera: a camera that needs 21 W won't run on a port capped at 15.4 W.
3. 100 Mbps ports for access points: they choke your Wi-Fi however good the AP is.
4. Runs over 100 m without EXTEND or fibre: the distant camera keeps dropping. Use EXTEND mode or an SFP port.

Buy PoE switches from Misbar Alhasibat

Misbar stocks network switches from Uniview, Grandstream and Huawei: unmanaged, cloud-managed and managed L2+, from 4 to 48 ports. Read our CCTV buying guide and best access point guide alongside this one to choose the devices the switch will power.

Prices on the store are final and include VAT, and you can split the payment with Tabby. Send us your camera and access point count and models on WhatsApp, and we will work out the PoE budget with you and suggest a switch.

Browse all network switches at Misbar →

FAQ

How do I choose a PoE switch?

Count your devices and add 20% spare ports, add up their wattage plus 25%, choose PoE+ if any device needs 802.3at, gigabit ports if you have access points, and a managed switch if you need VLANs.

How many watts do 8 security cameras need?

Most fixed cameras draw 5 to 6 W, so 8 cameras need about 50 W, or 60 to 65 W with headroom. Add 21 W for a PTZ camera if you have one.

Will a PoE switch damage my PC or TV?

No. IEEE-standard PoE switches detect the device first and only send power to devices that request it, so a PC just gets a network connection.

What is the difference between PoE and PoE+?

PoE (802.3af) delivers up to 15.4 W per port, and PoE+ (802.3at) up to 30 W for PTZ cameras and larger access points.

What if a camera is more than 100 m away?

Turn on EXTEND mode on a Uniview switch such as the NSW2010-10GT-POE-IN to reach up to 250 m, or place a second switch near the camera and link it over fibre through an SFP port.

Which PoE switch should you choose?

• Home or shop: the NSW2010-5GT-POE-IN-UK.
• Villa with cameras: the NSW2010-10GT-POE-IN.
• Villa or office with access points: the GWN7701PA.
• Warehouse or compound with many cameras: the NSW3000-24T1GT1GC-POE-IN.
• Office with a managed network: the GWN7802P or GWN7803P.
• Huawei network or 10G uplinks: the S220-24P4X.

This mosque sound system guide starts with the mosque, not the equipment. The number of areas you want to control decides the amplifier, the shape of each area decides the speaker type, and the total speaker wattage decides the power. We walk through 6 steps with real numbers, from splitting the mosque into zones to stopping feedback, and give you 3 ready setups for a small prayer room, a neighbourhood mosque and a large Friday mosque, all built from DSPPA equipment available at Misbar.

The parts of a mosque sound system

Step 1: Split the mosque into areas

Before buying anything, sketch the mosque and list every area that needs sound. Most mosques have 3 to 5:

• Main prayer hall: the largest and most important area.
• Women's section: often needs a different volume.
• Courtyard or outer area: fills up on Fridays and in Ramadan.
• Minaret or roof: for the adhan.
• Corridors, washrooms and wudu areas: low volume so latecomers hear the iqama.

Every area you want to turn up, down or off on its own needs its own zone on the amplifier. With 3 or more areas, you need a zoned amplifier; otherwise the outside gets louder every time you raise the prayer hall.

Step 2: Pick the right speaker for each area

We cover speakers in depth in our guide to the best mosque speakers. Here is the summary:

The two horns differ in a way that matters. The DSP1650 is IP66-rated and louder, up to 123 dB, but covers 280 Hz to 4.5 kHz, which suits the long reach the adhan needs. The DSP163HD is a 2-way horn covering 200 Hz to 15 kHz, so recitation in the courtyard sounds clearer.

[cta:1187592967]

Step 3: Add up the power and choose the amplifier

Mosque speakers run on a 100 V line, and each one has a transformer where you set its wattage. The method: add up every speaker's wattage, add 20 to 30% headroom, then pick the next amplifier size up.

Example for a mid-size neighbourhood mosque:

• Main hall: 8 DSP255IIW column speakers × 30 W = 240 W.
• Women's section: 6 DSP7011 ceiling speakers × 10 W = 60 W.
• Courtyard: 2 DSP1650 horns on the 25 W tap = 50 W.
• Total 350 W; with 25% headroom that is 437.5 W, so the 500 W DMA6500U covers it.

Why the DMA6 series? It has 6 zones with a volume knob each, 4 mic inputs with 48 V phantom power, a 24 V DC backup input and two ports for remote paging mics. We compare every DSPPA series in our DSPPA amplifier guide.

[cta:1919405398]

3 ready setups by mosque size

In the small prayer room, 6 × 10 W = 60 W, or 75 W with headroom, so the MP120UB is enough, paired with a D7821 two-mic kit for the imam and muezzin. In a large mosque whose speakers exceed 650 W, split the load: the zoned amplifier for the inside, and a DA-series power amplifier for the outside area fed from the LINE output.

Step 4: Choose the microphones

• Imam's mic at the mihrab: the CM30 is a unidirectional desk mic on a 455 mm stem, resistant to mobile phone interference, that picks up the imam and reduces everything around him. Note that it needs 48 V phantom power, which the DMA6 amplifiers provide; the MP120UB and MP250UB only offer 24 V phantom on their second input.
• Khateeb's mic: the D7822 kit includes a receiver, two wireless lavalier mics and two belt-pack transmitters, so the khateeb moves freely with his hands free. It offers 200 UHF channels and 150 m range in open space.
• Handheld mic for the muezzin and lessons: the D7821 kit has a receiver and two wireless handheld mics, with the same channels and range.

A two-mic kit gives you a ready spare: if the khateeb's battery dies on a Friday, the second mic takes over straight away.

[cta:1222881785]

Step 5: Stop feedback before it starts

Feedback happens when a mic picks up a speaker and the amplifier boosts it again in a loop. Prevention starts with installation: never point a speaker at the mihrab or minbar, keep speakers in front of the mic line rather than behind it, and don't run the hall louder than needed.

If feedback remains after that, the D6576 sits between the mic and the amplifier. Its SHARC processor detects the feedback frequency and cuts it automatically with 41 adaptive notch filters per input, plus a noise gate, compressor and 48 V phantom power. With two balanced inputs and outputs, it covers both the imam's and the khateeb's mic.

[cta:1953141]

Step 6: Add a paging mic for the office

In a large mosque, or one with a Quran school or admin office, you sometimes need to page one area without using the mihrab mic. The DMA20 is a gooseneck desk mic with 6 zone buttons, an all-zone call button and a chime. It connects to DMA6 amplifiers over CAT5e, up to 6 units on one port within 300 m, or a single unit up to 600 m.

Installation tips

• Speaker cable: a 100 V line lets you run long cables to the minaret and courtyard, but never mix 100 V and 8 Ω speakers on the same output.
• Zones: put the outside speakers on their own zone so you can switch them on and off without touching the prayer hall.
• Amplifier location: a well-ventilated cabinet near the mihrab, since mic cables should be shorter than speaker cables.
• Backup power: DMA6 amplifiers accept 24 V DC from a battery or supply, so sound continues through a power cut.

4 common mosque audio mistakes

1. A single-zone amplifier in a multi-area mosque: you can't lower the courtyard without the hall.
2. More speaker wattage than amplifier power: 500 W of speakers on a 350 W amplifier means distortion and an overheating amp.
3. An indoor speaker in the courtyard: ceiling speakers can't take sun and dust. Outside, use a horn or a water-resistant column.
4. One mic with no spare: a two-mic kit costs a little more and saves you a stopped khutbah.

Buy your mosque sound system from Misbar Alhasibat

Misbar stocks every part of a DSPPA mosque sound system in one place: single-zone and 6-zone amplifiers, column, wall, ceiling and horn speakers, wired and wireless microphones, plus the D6576 feedback suppressor and DMA20 paging mic. Browse all audio systems on the store.

Prices on the store are final and include VAT, and you can split the payment with Tabby. Send us your prayer hall size, number of areas and ceiling height on WhatsApp, and we will help you choose the number of speakers and the right amplifier.

Browse mosque sound systems at Misbar →

FAQ

How do I choose a mosque sound system?

Split the mosque into areas, pick a speaker for each, add up their wattage plus 25% headroom, then choose an amplifier with enough zones and more power than the total. Add a desk mic for the imam and a wireless kit for the khateeb.

How many watts does a mosque amplifier need?

It depends on total speaker wattage. A small prayer room with 6 speakers at 10 W needs 120 W; a neighbourhood mosque with 350 W of speakers needs 500 W with headroom.

Can I switch off the outside speakers during prayer?

Yes, if they are on their own zone in an amplifier like the DMA6350U, you turn them off with their knob without affecting the prayer hall.

Wired or wireless mic for the imam?

For the imam at the mihrab, a wired desk mic such as the CM30, since it stays put and needs no battery, provided the amplifier has a 48 V phantom input. For a khateeb who moves, a wireless lavalier such as the D7822.

How do I get rid of feedback in a mosque?

Start with the installation: don't aim speakers at the mic and keep the hall volume reasonable. If it continues, the D6576 detects the feedback frequency and cuts it automatically.

Which system should you choose?

• Small single-area prayer room: the MP120UB with DSP8064W speakers and a D7821 wireless mic kit.
• Neighbourhood mosque with three areas: the DMA6500U with column, ceiling and horn speakers, a CM30 and a D7822 kit.
• Large mosque with many areas: the DMA6650U with the D6576 feedback suppressor and the DMA20 paging mic.

With the DSPPA amplifier series explained side by side, the differences go well beyond wattage. MP is a compact mixer amplifier for simple spaces, DMA is a larger mixer amplifier with more inputs (some models split audio across 6 zones), and DA is a power amplifier with no mixer, built for large projects. This guide walks through each series using figures from DSPPA's official data, shows how to size the power you need, and points you to the model Misbar stocks for a mosque, school or shop.

Quick comparison: DSPPA amplifier series

In short: the MP250UB suits a shop or small prayer room, the DMA250U or DMA350U suits a single-space mosque, and the DMA6350U suits a mosque or school that needs to control each area separately. If you already have a mixer or processor and need serious power, choose from the DA series, such as the DA2250.

First: mixer amplifier or power amplifier?

This is the key distinction before any numbers. A mixer amplifier is one unit that combines mic inputs, music sources, level and tone controls, and amplification. You plug in the mic, your phone and the speakers, and it works. The compact MP models and the DMA series are mixer amplifiers.

A power amplifier only amplifies. It has no mic inputs, Bluetooth or tone knobs, and takes its signal from a mixer, processor or another amplifier. The DA series works this way, and so does the 650 W MP2500, despite its MP name.

DSPPA MP vs DMA: what actually differs

Both are mixer amplifiers with 100 V output for ceiling and column speakers, and both have Bluetooth, FM radio and USB playback. The difference shows when you compare two models of the same power:

The rule of thumb: one or two mics in one simple space, go MP; it is smaller and easier. If you need mics for the imam, the muezzin and a third speaker, or want an alarm system to cut the audio, DMA is the better fit.

MP series: compact amplifiers for shops, offices and prayer rooms

The MP60UB, MP120UB and MP250UB share one design at 60, 120 and 250 W. At 1.5U they sit on a shelf or in a small cabinet. Each has two mic inputs (a 6.3 mm jack on the front and an XLR on the back), two line inputs, Bluetooth, FM radio, USB MP3 playback and an IR remote.

• Priority: the emergency input and mic 1 override music, so the background source ducks when you speak.
• Output: 70 V and 100 V for ceiling and wall speakers on long cable runs.
• Backup power: the MP120UB and MP250UB take a 24 V DC input from a battery or power supply during outages.
• Phantom power: on mic 2 only, at 48 V on the MP60UB and 24 V on the MP120UB and MP250UB.

This series covers a shop, showroom, office or small prayer room with 20 to 30 ceiling speakers.

[cta:1529180283]

DMA series without zones: one mosque, one hall

From the DMA60U to the DMA650U, Misbar stocks 60, 250, 350 and 650 W models. All are 88 mm-high mixer amplifiers with 3 mic inputs, 2 AUX inputs, Bluetooth, FM and USB, plus control inputs for a siren, mute and EMC emergency signal.

One catch on the larger models: the DMA350U and DMA650U switch between 100 V and 4 to 16 Ω outputs, with no 70 V option. The DMA350U also drops to 175 W when running on 24 V DC.

[cta:1496130121]

The 6-zone DMA models: DMA6250U, DMA6350U, DMA6500U and DMA6650U

In a large mosque or school you often want the main prayer hall louder than the women's section, or the morning assembly in the yard without disturbing classrooms. That is what zones are for. The DMA6350U and its siblings have 6 zone outputs, each with its own volume knob and indicator, plus an FN button for zone selection.

• 4 mic inputs with 48 V phantom power, switched per input.
• Remote paging: two RJ-45 ports for DMA20 paging stations, up to 6 per port, over 300 to 600 metres, so an office or guard room can page a chosen zone.
• Built-in sources: USB, SD card, FM radio and Bluetooth, with an LCD display and remote.
• Clear priority order: mute, then emergency, then siren, then mic 1, then chime, then remote paging, then other sources.
• Backup power: a 24 V DC input for power cuts.

Power options: the DMA6250U at 250 W, the DMA6350U at 350 W, the DMA6500U at 500 W and the DMA6650U at 650 W. Everything else is the same, so choose by your total speaker wattage.

[cta:1919405398]

DA series: Class-D power amplifiers for large projects

Class-D delivers high power with less heat and lower consumption than traditional designs, which is why DA models fit 2 or 4 channels into just 1U. Each channel drives its own area at 70 V or 100 V, selected by a rear switch.

• Two channels: the DA2250 at 250 W per channel and the DA2500 at 500 W per channel.
• Four channels: the DA4060 at 60 W, the DA4125 at 120 W and the DA4250 at 250 W per channel.
• Single high-power channel: the DA3650 at 750 W and the DA3850 at 1500 W on 100 V output.

The 2- and 4-channel DA models offer a balanced line input, a balanced priority input, a 100 V priority input for emergency messages and a line output to chain another amplifier. They run on 24 V DC with a 3 dB power reduction, and include thermal and short-circuit protection plus a temperature-controlled fan.

[cta:1313094209]

How to size the amplifier you need

Ceiling and column speakers in mosques and schools usually run on a 100 V line, with a transformer on each speaker that lets you pick its power, such as 3 or 6 W. That line lets you connect dozens of speakers on long cable runs without calculating ohms.

1. Add up the wattage of every speaker on the line. Example: 30 ceiling speakers × 6 W = 180 W.
2. Add 20 to 30% headroom so the amplifier isn't running flat out all the time: 180 × 1.25 = 225 W.
3. Pick the next power rating up: here the 250 W MP250UB or DMA250U is enough.
4. If speakers are spread across areas you want to control separately, size each area on its own and choose a zoned DMA or a multi-channel DA.

To choose the speakers themselves, read our guide to the best mosque speakers.

4 common mistakes when buying a DSPPA amplifier

1. Buying a power amp with no mixer: a DA unit won't take a mic directly. Without a mixer, buy an MP or DMA mixer amplifier.
2. Running at the limit: 250 W of speakers on a 250 W amplifier means it always runs at full power. Leave headroom.
3. Mixing 100 V and 8 Ω speakers on one output: each type uses a different amplifier output, and they can't share one line.
4. A large mosque on a single-zone amp: you can't turn one area down without the rest. Choose the DMA6350U or another 6-zone model.

Buy DSPPA amplifiers from Misbar Alhasibat

Misbar stocks DSPPA amplifiers across all three series: the compact MP models, DMA in single-zone and 6-zone versions with the DMA20 paging station, and DA power amplifiers with one, two or four channels. You will find every DSPPA product, including speakers, microphones and PA systems, on the brand page.

Prices on the store are final and include VAT, and you can split the payment with Tabby. Send us your speaker count, wattage per speaker and number of areas on WhatsApp and we will help you choose the right amplifier.

Browse all amplifiers at Misbar →

FAQ

What is the difference between DSPPA MP and DMA amplifiers?

Both are mixer amplifiers. MP is smaller (1.5U) with two mic inputs and up to 250 W. DMA is larger (2U) with three mic inputs and up to 650 W, and includes 6-zone models with remote paging.

Which DSPPA amplifier suits a mosque?

For a single-space mosque, the DMA250U or DMA350U depending on speaker count. For a large mosque with a women's section, courtyard and minaret, the 6-zone DMA6350U.

When do I need a DA power amplifier?

When you already have a mixer or processor and need more power or separate channels for many areas. The DA4250, for example, delivers 4 channels at 250 W each in 1U.

Will the amplifier keep working during a power cut?

The MP120UB and MP250UB, the 6-zone DMA models and the 2- and 4-channel DA models have a 24 V DC input for a battery or backup supply, though power may drop when running on it.

What about the PV series?

The PV series is not currently available at Misbar, and we found no product page or datasheet for it on DSPPA's official site. If you need a power amplifier, the DA series is the available alternative.

Which DSPPA amplifier should you choose?

• Shop, office or small prayer room: the MP120UB or MP250UB.
• Single-space mosque or hall: the DMA250U or DMA350U.
• Mosque or school with several areas: the DMA6350U with the DMA20 paging station.
• Large project with a mixer or processor: the DA2250 or DA4250.
• One area that needs very high power: the 1500 W DA3850.

Buying security cameras for a villa, office or warehouse comes down to four choices: the right camera type for each spot, the resolution you actually need, the kind of night vision, and the recorder that ties it all together. This CCTV buying guide for Saudi Arabia walks through each choice with real numbers and matches every location to a Uniview camera you can order from Misbar today.

Quick pick: which camera fits your site?

Start with where the camera goes

An indoor camera in an air-conditioned office lives a very different life from one on a yard wall in summer sun and dust. For outdoor spots, choose IP67, which means fully dust-tight and water-resistant. If the camera is within reach, at a building entrance or shopfront, add an IK10 vandal-resistant housing like the IPC328LE-ADF28K-H dome.

Then decide how wide the view should be. A 2.8 mm lens covers roughly 100°, which suits rooms, corridors and villa entrances. A 4 mm lens is narrower, 79° on the IPC2A14LP-ADF40KC-4G-E, but shows more detail further away.

Security camera types and where each one fits

Dome cameras for ceilings and indoor spaces

Domes sit flush on the ceiling and hide where they point. The IPC325LB-SF28-A is a 5MP dome with a 97° view and 30 m night vision, and it has no microphone, which makes it a good choice for offices and clinics that want clear video without recording conversations. Browse all dome cameras.

Bullet cameras for walls and entrances

Bullets are easy to spot, and that alone deters people. The IPC2128LB-ADF28K-DL is a compact 8MP bullet with a 2.8 mm lens covering 100.8° and dual light to 30 m. At 0.25 kg it mounts easily over a villa gate or shopfront. Browse bullet cameras.

Turret (eyeball) cameras for car parks and warehouses

Turrets combine the compact size of a dome with the easy aiming of a bullet, and there is no clear bubble in front of the lens to reflect infrared at night. The IPC3618LE-ADF28KC-DL records 8MP (3840×2160) across 98.7°, with dual light to 30 m and two-way audio. Browse turret cameras.

PTZ cameras for large open areas

A PTZ camera pans, tilts and zooms, so one unit can watch a whole yard and zoom in on a plate or a face when needed. The IPC6424SR-X25-VF pairs a 4MP sensor with 25x optical zoom (4.8 to 120 mm), 100 m infrared and auto tracking, which suits compound car parks and warehouse perimeters.

Wi-Fi and 4G cameras where there is no cable

When running a network cable is not practical, a Wi-Fi camera connects straight to your router. The Uho-B2D-M5F4D is a 5MP IP67 bullet for villa gates and garage doors, and the Uho-P1A-M5F4D turns 345°, follows people on its own and sounds a light-and-siren warning.

For farms, istirahas and job sites with no internet at all, use a camera that runs on a mobile SIM: the fixed 4MP IPC2A14LP-ADF40KC-4G-E, or the 3MP pan-and-tilt Uho-P2G-M3F4D-AS with microSD up to 512GB. Browse Wi-Fi cameras and 4G cameras.

[cta:59235951]

Resolution: is 5MP enough, or do you need 8MP (4K)?

Resolution decides how much detail survives when you zoom into the footage. In rooms, corridors and offices people are close to the camera, so 5MP is usually enough. For outdoor entrances, car parks and yards, where you want to recognize a face or a car several metres away, go for 8MP such as the IPC328LE-ADF28K-H or IPC3618LE-ADF28KC-DL.

Higher resolution also means bigger files and more storage on the recorder, so match resolution to how important each spot is instead of using 8MP everywhere. For car park barriers that need number plate reading, Misbar also stocks dedicated plate recognition cameras in the security cameras range.

Night vision: infrared or full color at night?

Most cameras use infrared (IR), which gives a black-and-white picture in total darkness. On the models in this guide, IR range runs from 20 to 100 m. Dual light adds a warm light so the picture switches to color and you can tell the color of a car or clothing.

If you want color all night, the IPC3638SE-ADF28K-WP-I1 from the OwlView Plus series keeps a color image down to 0.0003 lux with a 1/1.2" sensor and F1.0 lens, backed by 30 m warm light. It fits hotel entrances, car parks and shopfronts.

[cta:1742573677]

Choosing a recorder: NVR or DVR?

The recorder collects footage from every camera, stores it on a hard drive and lets you watch live and recorded video on your phone. The camera type decides which recorder you need:

• NVR for IP cameras: every camera above is an IP camera and needs an NVR. The NVR301-04S3-P4 takes 4 cameras and powers them through 4 built-in PoE ports with a 54 W budget, so a small villa or shop needs no separate switch. Browse NVR recorders.
• DVR and XVR for analog cameras: if the site already has coax cabling, upgrade the picture with a modern analog camera such as the 5MP UAC-B115-AF28, with a 102.2° view and built-in microphone, paired with an XVR instead of rewiring.

We cover the full difference in NVR vs DVR vs XVR. How long recordings are kept depends on drive capacity, camera count and resolution, so use a surveillance-rated hard drive built for recording around the clock.

[cta:1403243449]

Power and network: when do you need a PoE switch?

PoE carries power and data to the camera over one network cable. If you have more cameras than PoE ports on the recorder, or the cameras sit far from it, add a PoE switch and check that the total camera draw stays under the switch budget.

Wi-Fi cameras need a strong signal where they are mounted. If the signal is weak in the yard or annex, an outdoor access point fixes it, as covered in our guide to the best access points for villas and businesses.

4 common mistakes before buying CCTV

1. Wrong lens for the distance: 2.8 mm is wide for close areas; 4 mm or zoom is for distance.
2. Ignoring privacy: in offices and clinics, pick a camera without a microphone such as the IPC325LB-SF28-A.
3. Not checking the PoE budget: total camera draw must stay below the recorder budget, 54 W on the NVR301-04S3-P4.
4. Wi-Fi camera too far from the router: a weak signal drops the stream, so test the signal first or choose a PoE camera.

Buy security cameras and NVRs from Misbar Computers

Misbar stocks the full Uniview range: dome, bullet, turret, PTZ, Wi-Fi and 4G cameras, together with NVR recorders and PoE switches. Fitting out a villa? Complete the setup with a villa intercom kit.

Prices on the store are final and include VAT, and you can split the payment with Tabby. Not sure which model suits your site? Message us on WhatsApp.

Browse all security cameras at Misbar →

FAQ

Does a Wi-Fi camera keep recording if the internet drops?

If it has a memory card, it keeps recording to the card, and remote viewing resumes when the connection returns. The Uho-P2G-M3F4D-AS, for example, takes a card up to 512GB.

How many cameras can I run without a switch?

The NVR301-04S3-P4 powers 4 cameras straight from its ports. For more than 4, add a PoE switch or choose a recorder with more ports.

Do I need to replace coax cabling to get a sharper picture?

Not necessarily. Modern analog cameras like the UAC-B115-AF28 deliver 5MP over existing coax when paired with an XVR.

What is the difference between a 2.8 mm and a 4 mm lens?

A 2.8 mm lens is wider, around 100°, for nearby areas. A 4 mm lens is narrower, about 79°, but shows more detail at a distance.

Can I watch the cameras on my phone?

Yes. Uniview cameras and recorders can be viewed through the brand mobile app, as long as the recorder or camera is connected to the internet.

Which setup should you choose?

• Apartment or small home: one or two Wi-Fi cameras such as the Uho-B2D-M5F4D.
• Villa with network cabling: 4 IP cameras on the NVR301-04S3-P4, domes inside and 8MP bullets or turrets at the entrances.
• Farm or istiraha with no internet: a 4G SIM camera like the IPC2A14LP-ADF40KC-4G-E.
• Warehouse or compound car park: 8MP turrets for corners, a PTZ for the yard, and a PoE switch.

The recorder collects footage from every camera, stores it, and is what you watch from on your phone. You do not pick it by price. You pick it by the cameras and cabling you have. This guide puts NVR vs DVR vs XVR side by side in one table, then matches a Uniview recorder to each case: a brand-new system, or an older coax system you want to upgrade.

NVR vs DVR vs XVR at a glance

In short: for a new installation, choose an NVR. If you already have working analog cameras on coax, choose an XVR rather than a DVR, because it takes the same cameras and adds IP channels.

What is a DVR?

A DVR records analog cameras. The camera sends its picture over coax, the recorder converts it to digital video and saves it to the hard drive, and every camera needs its own power adapter. You still find DVRs in many older shops and villas, but they cannot take IP cameras, which is why the XVR has replaced them.

What is an XVR?

An XVR is a hybrid recorder. It works with analog cameras on all four standards (AHD, TVI, CVI and CVBS) and adds channels for IP cameras, so you keep your existing cameras and cabling and add IP cameras whenever you need them.

• XVR301-04G3: records 4 analog cameras up to 5MP plus 2 IP cameras. A good fit for small villas, shops and istirahas replacing an old DVR.
• XVR301-08Q3: records 8 analog cameras up to 8MP plus 4 IP cameras (up to 12), with perimeter protection and 4 alarm inputs. Suited to schools, warehouses and compounds.

To get a sharper picture on existing coax without rewiring, swap old cameras for a modern analog model such as the UAC-B115-AF28, a 5MP bullet with a 102.2° view, built-in microphone and 20 m night vision.

[cta:1714162522]

What is an NVR?

An NVR records IP cameras only. Each camera processes its own image and sends it digitally over the network cable, which allows higher resolution. Most modern NVRs also have PoE ports, so one network cable carries both power and video and you do not need an adapter at every camera.

Uniview NVRs by camera count:

If your NVR has no PoE ports, or you have more cameras than ports, add a PoE switch such as the 16-port Uniview NSW2010-18GT2GP. Browse all NVR recorders.

[cta:1403243449]

When is it worth moving from coax to an NVR?

If your coax is old or damaged, or you want features analog cameras cannot offer, such as two-way audio and person detection inside the camera, moving to an NVR is the better choice. And if you are re-cabling anyway for a renovation or extension, run network cable instead of coax, since one cable carries both power and video with PoE.

If the cabling is sound and your current cameras are good enough, an XVR raises the resolution and puts off the cost of re-cabling, and you can add IP cameras to the same recorder later.

Which recorder should you choose?

• Working coax cameras already installed: an XVR, so you keep the cameras and add IP later.
• New system for a villa or shop with 4 cameras: the NVR301-04S3-P4 with IP cameras such as the IPC328LE-ADF28K-H dome.
• Two-storey villa with 5 to 8 cameras: the NVR301-08S3-P8 or NVR501-08B-P8.
• Warehouse or school with 16 cameras: the NVR502-16B-P16, with built-in PoE and two drive bays.

Whichever recorder you choose, fit a surveillance-rated hard drive built for recording around the clock. How long footage is kept depends on drive capacity, camera count and resolution.

Buy CCTV recorders from Misbar Alhasibat

Misbar stocks Uniview recorders in every size, together with security cameras of all types, including dome and bullet models, and PoE switches to grow the system. Starting from scratch? Read our CCTV buying guide to choose the cameras before the recorder.

Prices on the store are final and include VAT, and you can split the payment with Tabby. Not sure how many channels you need? Message us on WhatsApp.

Browse all recorders at Misbar →

FAQ

Can I connect an IP camera to a DVR?

No. A DVR works with analog cameras only. To mix both types, choose an XVR, or move fully to an NVR.

Does the recorder keep recording without internet?

Yes. Recording happens on the hard drive inside the recorder. Internet is only needed to watch from your phone away from the site.

Do I need a switch with an NVR?

Not if the recorder has enough PoE ports for your cameras, like the NVR301-04S3-P4 for 4 cameras. You need one if the recorder has no PoE or you have more cameras than ports.

Can I replace an old DVR with an XVR and keep my cameras?

In most cases, yes, because Uniview XVRs support all four analog standards: AHD, TVI, CVI and CVBS. Just check which standard your current cameras use.

How many hard drives does a recorder take?

Smaller models like the NVR301-08S3-P8 have one bay for a drive up to 10TB, while the NVR502-16B-P16 has two bays for drives up to 24TB each, so it keeps footage for longer.

FXS vs FXO in one line: an FXS port is where you plug in an analog phone or fax, and an FXO port is where you plug in the landline from STC. If your company has moved to an IP PBX but still has a landline, a fax machine or old phones in rooms, you will need one or both. This guide explains the difference with examples and shows which Grandstream or Yeastar adapter, gateway or module fits your setup.

FXS and FXO at a glance

An easy way to remember it: FXS acts like the phone socket in the wall, giving dial tone to whatever you plug in. FXO acts like the phone itself, so it needs something to give it dial tone, and that is the landline.

What you need for your setup

ATAs: FXS ports for analog phones and fax

An ATA is a small box that turns an analog phone into a PBX extension. Plug the phone or fax into the FXS port and the ATA into the network, and it registers on the PBX with a SIP account like any IP phone.

• Grandstream HT801 V2: one FXS port and a 10/100 network port. It sends fax over T.38 and falls back to G.711 automatically when the other side doesn't support it, and encrypts calls with TLS and SRTP. It runs on a 5V/1A Micro USB adapter and does not support PoE.
• HT802: the same idea with two FXS ports, for two phones or a phone plus fax.
• HT818 V2: 8 FXS ports, two gigabit network ports and a 12V/1.5A adapter. A good fit for a warehouse or older building full of analog phones.

These adapters are especially handy for fax. Many companies still receive faxes from government bodies or suppliers and don't want a separate machine on a dedicated line.

[cta:1801726387]

High-density FXS gateways: Grandstream GXW4200 for hotels and hospitals

When a building has dozens of analog phones, such as an older hotel or a hospital, you can connect them all to one gateway instead of replacing every handset. The GXW4200 series comes in four sizes: the GXW4216 with 16 ports, the GXW4224 with 24, the GXW4232 with 32 and the GXW4248 with 48.

Each port has its own SIP account, so every phone appears as a separate extension on the PBX. The gateway mounts in a 1U 19-inch rack and includes overvoltage and overcurrent protection. The GXW4216 has front RJ11 ports plus a 50-pin Telco connector, while the GXW4248 uses two Telco connectors only, so it is built to terminate on a patch or distribution panel.

Grandstream HT813: FXS and FXO in one box

The HT813 suits a small office or branch with one landline and one analog phone. The FXO port takes the STC line and presents it as a trunk on the PBX, while the FXS port connects an analog phone or fax as an extension. It also supports Lifeline on the PSTN line.

It has two 10/100 network ports (LAN and WAN) with a built-in NAT router, runs on a 12V/0.5A adapter and does not support PoE.

[cta:388913085]

FXO gateways: bringing STC landlines into an IP PBX

An FXO gateway takes your landlines and turns them into SIP trunks on the PBX, so staff make and receive calls on the same landline numbers from IP phones. The number of FXO ports matches the number of landlines, not the number of staff.

• Yeastar TA410 and TA810: 4 and 8 RJ11 FXO ports with a 10/100 LAN port. They speak SIP and IAX2 and include a firewall, IP blocklist and intrusion alerts. Yeastar lists compatibility with Asterisk, FreePBX and Lync Server.
• TA1610: 16 FXO ports on an RJ21 connector with LAN and WAN ports, for companies with many lines.
• Grandstream HT841 and HT881: 4 and 8 FXO ports plus one FXS port. During a power cut, the FXS port connects straight to the last FXO port, so one analog phone still works on the landline. They run on 802.3af PoE or a 12V adapter.

[cta:109578012]

Yeastar PBX modules: O2, S2 and SO

If you run a Yeastar P-Series or S-Series PBX, you don't need an external gateway for a few ports. The module goes inside the PBX itself:

• O2: two FXO ports for two landlines.
• S2: two FXS ports for two analog phones or a fax.
• SO: one FXS and one FXO port together.

They fit directly in the P520 and P550, in the P560 and P570 via the EX08 expansion board, in the S20 and S50, and in the S300 via the EX08. The PBX sets the limit: the P520 has two slots, so up to 4 FXS and 4 FXO ports, and the P550 has four slots, so up to 8 of each.

[cta:325672214]

Grandstream UCM6300: the ports are built in

Before buying a gateway, check your PBX. Grandstream UCM6300 models include built-in FXS and FXO ports: the UCM6301 has one of each, the UCM6302 two, the UCM6304 four and the UCM6308 eight of each with Lifeline support. With only a few landlines, the built-in ports may be all you need.

No landline? Use SIM cards instead of FXO

Many newer companies have no landline at all and use mobile numbers from STC, Mobily or Zain. In that case you don't need FXO but a SIM gateway such as the Yeastar TG400L, with 4 4G LTE ports and one SIM per port. Staff call and answer on the mobile numbers from their desk phones, and calls are spread across the SIMs.

4 common mistakes

1. Plugging a landline into an FXS port: both supply voltage, so it won't work and may damage the port. The line always goes on FXO.
2. Counting FXO ports by headcount: you need one FXO port per landline. Two landlines need two ports even with 30 staff.
3. Forgetting the power adapter: the HT801 V2 and HT813 don't support PoE, so they need a socket nearby.
4. Buying a gateway when your PBX already has ports: check the UCM6300 ports or Yeastar module slots first.

Buy VoIP gateways and ATAs from Misbar Alhasibat

Misbar stocks ATAs and FXS and FXO gateways from Grandstream and Yeastar, the O2, S2 and SO modules and EX08 board for Yeastar PBXs, 4G SIM gateways, and the PBX systems themselves. Browse Yeastar and Grandstream on their brand pages.

Prices on the store are final and include VAT, and you can split the payment with Tabby. Send us your PBX model and the number of landlines and analog phones on WhatsApp, and we will help you pick the right device.

Browse PBX systems and VoIP gateways at Misbar →

FAQ

What is the difference between FXS and FXO?

An FXS port is for analog phones and fax and supplies their dial tone. An FXO port is for the landline from the telecom provider and receives dial tone from it.

How do I connect an STC landline to an IP PBX?

Through an FXO port: built into the PBX like the UCM6302, an O2 module in a Yeastar PBX, or an external FXO gateway such as the TA410.

How do I connect a fax machine to an IP PBX?

Through an FXS port. The simplest option is the HT801 V2, which supports T.38 fax. Make sure your PBX and provider support T.38 as well.

What does Lifeline mean?

A direct connection between an FXS and an FXO port during a power cut, so one analog phone keeps working on the landline. You will find it on the HT841, HT881 and the UCM6308 ports.

Is an internal PBX module better than an external gateway?

For a few ports, a module is simpler because it sits inside the PBX with no separate power or network. For many ports, or a PBX with no free slots, an external gateway is the answer.

What to buy

• One fax or analog phone: the HT801 V2.
• Small office with a landline and an analog phone: the HT813.
• 4 landlines: the TA410, or the HT841 if you want Lifeline.
• Hotel or hospital with many analog phones: the GXW4216 to GXW4248.
• Yeastar P520 or P550 PBX: the O2 for lines and the S2 for phones.
• No landline: the TG400L SIM gateway.

Choosing the best mosque speakers starts with the space, not the wattage. A large prayer hall with a high ceiling and marble floor needs a different speaker from a women's prayer area under a drop ceiling, and the courtyard needs a third type. This guide matches every part of the mosque to a DSPPA speaker with real numbers, then shows how to pick the amplifier and microphones that complete the system.

Quick pick: which speaker for which area?

All of these run on a 70V or 100V line, so you can wire many of them to one amplifier over long cable runs without the sound dropping off.

Column speakers for large halls and high ceilings

A column speaker is tall and slim and aims sound at the rows of worshippers rather than at the ceiling, which cuts echo in wide halls with high ceilings and marble floors. The DSP255IIW is a white 30W column with a slim aluminium body that blends into light walls and a built-in 70V/100V transformer, and it works in the hall or a covered courtyard.

For smaller halls, the DSP6114W is a lighter white column at 20W, 89 dB sensitivity and 3 kg, and it still carries speech clearly to the back rows.

[cta:1187592967]

Wall speakers for pillars and side walls

Wall speakers mount on pillars and walls with a bracket angled towards worshippers, and they suit mid-size halls with standard ceilings. The DSP8064W is a white 40W wall speaker with a separate tweeter for clear speech and taps for 70V or 100V lines. For halls that need more output, the DSP8063W delivers 30W from a 5-inch woofer and reaches 105±2 dB.

[cta:1045550652]

Ceiling speakers for the women's hall and corridors

Ceiling speakers sit inside the drop ceiling out of sight and spread sound evenly from above. The DSP7011 is a frameless 6.5-inch speaker rated 10W that fits a 165 to 170 mm cutout with its included clamps, a good match for women's prayer areas, corridors and ablution rooms.

Under a high ceiling, choose the DSP8011: 94 dB sensitivity and 104 dB maximum SPL give you more level from the same amplifier power, at 10W on a 100V line or 5W on 70V.

Horn speakers for the courtyard

Horns are built for open areas and throw sound further than indoor speakers. The DSP1650 is a 50W IP66 horn with an ABS bell, a metal bracket and 6 to 50W taps on a 100V line. If voice clarity in the courtyard matters most, the DSP163HD is a two-way horn giving 25W on a 100V line across 200Hz to 15kHz.

[cta:985243419]

Amplifier and microphones: the rest of the system

100V speakers need a constant-voltage amplifier. The MP1000PIII is a 350W mixer amplifier with 3 mic inputs, 2 AUX inputs, 70V, 100V and P1 outputs, and priority for MIC1 over everything else, which suits the Friday khutbah and lessons.

To check the amplifier is big enough: add up the speaker taps you will use and leave some headroom. For example, 12 DSP7011 ceiling speakers at 10W (120W) plus 6 DSP255IIW columns at 30W (180W) come to 300W, within the 350W of the MP1000PIII.

For microphones, the CM30 is a minbar desk mic with a 455 mm tube and a metal base that needs 48V phantom power, so check your mixer provides it. For a khateeb who moves, the D7822 is a wireless kit with two lavalier mics, and for lessons and events the D5821 gives you two wireless handhelds. Browse all microphones.

[cta:115916357]

Common mistakes with mosque speakers

1. Mixing 100V and 8-ohm speakers on one output: keep each type on its own output; the MP1000PIII has both.
2. Ordinary speakers in a marble hall with a high ceiling: echo swallows speech, and column speakers reduce it.
3. Overloading the amplifier: add up the speaker taps before you buy, as in the example above.
4. A horn inside the hall: horns are for open areas; indoors they sound harsh.

Buy mosque speakers from Misbar Alhasibat

Misbar stocks a complete DSPPA mosque sound system: column, wall, ceiling and horn speakers, amplifiers, and wired and wireless microphones. Browse all audio systems to complete the setup.

Prices on the store are final and include VAT, and you can split the payment with Tabby. Want help working out speaker count and amplifier power for your mosque? Message us on WhatsApp.

Browse all speakers at Misbar →

FAQ

How many speakers can a 350W amplifier run?

It depends on each speaker's tap. For example, 12 ceiling speakers at 10W plus 6 columns at 30W add up to 300W, which runs on the MP1000PIII with headroom to spare.

What is the difference between the DSP255IIW and the DSP6114W?

Both are white column speakers. The DSP255IIW is stronger at 30W with an aluminium body, while the DSP6114W is lighter at 20W and 89 dB sensitivity, better for smaller halls.

Can I use a horn speaker inside the prayer hall?

No. Horns are designed for open areas. Inside the hall, use column, wall or ceiling speakers.

When should I choose the DSP8063W over the DSP8064W?

Pick the DSP8064W at 40W with its separate tweeter when speech clarity comes first, and the DSP8063W at 30W when you need high output, up to 105±2 dB, in a wide or crowded hall.

Does the women's prayer hall need its own amplifier?

Not necessarily. Its ceiling speakers can share the same amplifier as long as the total power stays within its rating. If you want to control their volume separately, put them on their own line.

Do 100V speakers need a special amplifier?

Yes, a constant-voltage amplifier with a 70V or 100V output such as the MP1000PIII. A standard 8-ohm home amplifier will not drive them.

The short version

Column speakers for the large hall, wall speakers for pillars and walls, ceiling speakers for the women's hall and corridors, and a horn for the courtyard. Add up the speaker power before choosing the amplifier, then finish the system with the right mic for the minbar and lessons.

The best access point in Saudi Arabia for your villa or office is the one that suits where it is mounted and how many devices will connect to it, not the most expensive one. Villa Wi-Fi drops between floors because of concrete slabs, and office Wi-Fi slows down when dozens of staff connect at once. This guide compares 10 Grandstream and Huawei models that Misbar stocks, covering ceiling, wall and outdoor units on Wi-Fi 6 and Wi-Fi 7, and matches each one to a space using real numbers.

Quick comparison: the right access point for each space

In short: the GWN7660E fits most villas and small offices, the GWN7660EM covers a room no cable reaches, and the GWN7661E suits hotel rooms. Companies building on Huawei should look at the AP362E, busy halls need the GWN7664E, and Wi-Fi 7 buyers can pick the GWN7670E or AP371. For courtyards, pools and car parks, choose the GWN7660ELR or AP771.

How to choose an access point: 4 questions first

1. Where will it go? A ceiling unit spreads signal across the whole room, a wall unit suits rooms and corridors, and an outdoor unit handles sun and dust in courtyards and parking areas.
2. How many devices at once? Count phones, laptops, TVs and cameras. A villa with a large family is a different load from a training room with 100 people.
3. Does a network cable reach the spot? Most models run on PoE, so one cable from a PoE switch carries both power and data. If no cable reaches, a Mesh unit can connect wirelessly.
4. How will you manage it? Grandstream units include a built-in controller for up to 50 access points, plus the free GDMS Networking cloud. Huawei eKit units are managed from the HUAWEI eKit app and SNC cloud, or from a WAC controller.

Grandstream GWN7660E: the go-to access point for villas and small offices

The Grandstream GWN7660E is where most villa setups start. It is a dual-band AX3000 Wi-Fi 6 unit, with up to 2402 Mbps on 5GHz and 573.5 Mbps on 2.4GHz, handles 256 connected devices, and reaches up to 175 metres depending on the space.

• Ceiling or wall mounting, with the mounting kit in the box.
• One gigabit port powered by 802.3af or 802.3at PoE, drawing 12.95 W at most. No power adapter in the box.
• 32 SSIDs, so family, guest and camera networks stay separate.
• WPA3, secure boot and a unique default password on every unit.

Fit two or three of them and one acts as the controller for the rest, so you manage the whole villa network from one place with no extra hardware.

[cta:1548450124]

No cable to the room? The GWN7660EM plugs into the wall socket

In finished villas, network cable rarely reaches the annex, driver's room or outdoor majlis. The GWN7660EM mounts in place of a wall power socket and takes power straight from it (110 to 240 V), then links wirelessly to another Grandstream access point in the house over Mesh. Press the SYNC button and it joins the network.

You get the same AX3000 speed class, 128 connected devices, up to 120 metres of range and a gigabit port for a wired TV or PC. It supports 802.11k/v/r fast roaming, so calls don't drop as you walk between rooms. Note that it does not take PoE; it needs the socket.

In-wall access points for hotels and rooms: GWN7661E and Huawei AP160

The Grandstream GWN7661E sits inside the wall like a light switch, so there is nothing on the ceiling. It covers the room with Wi-Fi 6 for up to 256 devices and adds 3 front gigabit ports, two of which supply PoE at up to 6 W each. Plug the room's IP phone or TV into it with a short cable.

That makes it a good fit for hotel rooms, serviced apartments and staff offices. With both PoE outputs in use it can draw up to 25 W, so run it from an 802.3at PoE+ switch.

Huawei's alternative is the AP160, which fits an 86 mm wall box with two gigabit ports and 1.775 Gbps Wi-Fi 6. Huawei recommends 48 users, with 128 as the maximum, and an optimal signal distance of 15 metres, so it is built for a single room or small office.

[cta:1440466511]

Huawei AP362E: a ceiling access point for company offices

The Huawei AP362E belongs to the HUAWEI eKit line. It is dual-band Wi-Fi 6 at 2.975 Gbps (2.4 Gbps on 5GHz and 0.575 Gbps on 2.4GHz) with channels up to 160 MHz. It runs on 802.3af PoE at no more than 9.4 W, so any standard PoE switch will power it.

What sets it apart is its three operating modes: standalone (Fat AP), controller-managed (Fit AP with a WAC), or cloud-managed through SNC. You can start with two units in a small branch on the HUAWEI eKit app and move them under a controller as the network grows. It supports 802.11k/v/r roaming and WPA3, and its IP41 rating means indoor use only.

[cta:383991048]

Wi-Fi 7 access points: Grandstream GWN7670E and Huawei AP371

Wi-Fi 7 (802.11be) adds MLO, which lets a device connect on two bands at once, and 4096-QAM for higher throughput. You only get the full benefit if your phones and laptops support Wi-Fi 7; older devices connect at Wi-Fi 6 speeds.

• Grandstream GWN7670E: BE3600 class, up to 2882 Mbps on 5GHz and 688 Mbps on 2.4GHz, 512 connected devices, and a 2.5G port powered by 802.3at PoE. It supports Mesh and fast roaming and mounts on a ceiling or wall.
• Huawei AP371: 3.57 Gbps with a 2.5GE port. Huawei recommends 150 users with a 256 maximum, and it runs on 802.3af/at PoE or a 12 V adapter.

The 2.5G port matters. If your fibre line is faster than 1 Gbps, an access point with a 1G port becomes the bottleneck. To use that port fully, the switch port feeding it must be 2.5G too.

[cta:955940949]

Halls, schools and crowded spaces: GWN7664E

In a meeting hall, training room, prayer hall or restaurant, the challenge is device count rather than floor area. The Grandstream GWN7664E has 8 antennas in 4×4:4 on both bands, 6 Gbps of combined wireless speed and room for 512 devices. It comes with two 2.5G ports, runs on 802.3at PoE and draws up to 21 W.

Outdoor access points for courtyards, pools and car parks

Indoor units should stay indoors: summer heat and dust shorten their life. These outdoor models are built for it:

• Grandstream GWN7660ELR: Wi-Fi 6 with up to 300 metres of range and 256 devices, operating from -30 to 60°C in a weather-resistant housing. It mounts on a wall or pole with up to 60 degrees of tilt, and has a 1G port plus a 2.5G SFP port for a fibre link. It runs on PoE; no PoE injector is included.
• Huawei AP771: Wi-Fi 7 at 3.57 Gbps with IP65 dust and water protection, operating from -30 to 60°C. Huawei recommends 130 users with a 256 maximum and an optimal coverage distance of 130 metres. It has a 2.5GE port and runs on PoE only.

They also suit istirahas, farms, warehouse yards and compound car parks, and can bring Wi-Fi to cameras out there that connect wirelessly.

[cta:772905037]

How many access points does a villa need?

The concrete slab between floors blocks most of the signal, so one unit on the ground floor won't cover the upper floor well, however powerful it is. A practical starting point: at least one access point per floor, one for the annex, and an outdoor unit if you want Wi-Fi in the courtyard or by the pool. On a large floor or one with many walls, two units beat one in the middle.

Keep every unit on one brand so you manage them in one place and your phone moves between them without dropping. Grandstream units work together through the built-in controller and Mesh; Huawei units through the eKit app and controller.

Switch and power: 802.3af or 802.3at PoE?

Every model in this guide runs on PoE except the GWN7660EM. The real question is which PoE standard each one needs, so you can pick a PoE switch that can power it:

• 802.3af is enough: Huawei AP362E (9.4 W) and AP160 (9.1 W).
• Run on af or at: GWN7660E (12.95 W), GWN7660ELR (13 W), Huawei AP371 (13.3 W) and AP771 (18.8 W).
• Need 802.3at (PoE+): GWN7670E, GWN7664E (21 W), and the GWN7661E when its PoE outputs are in use.

Add up the draw of every unit and make sure the switch's PoE budget covers it. Without a PoE switch, note that most of these units ship without a power adapter.

4 common mistakes when buying access points

1. An indoor unit in the courtyard: heat and dust will damage it. Outdoors, choose the GWN7660ELR or AP771.
2. One unit for a two-storey villa: the concrete slab blocks the signal, so put one on each floor.
3. A PoE switch that falls short: units like the GWN7670E and GWN7664E need PoE+, and an af-only switch won't power them.
4. Mixing brands on one network: you lose central management and smooth roaming. Pick one brand for the whole network.

Buy access points from Misbar Alhasibat

Misbar stocks access points from Grandstream and Huawei: ceiling, wall and outdoor, on Wi-Fi 6 and Wi-Fi 7. Pair them with the PoE switches that power them over one cable, and with Wi-Fi extenders and Mesh units for spots no cable reaches. If you are fitting out a whole villa, read our guide to the best villa intercom too, since the indoor screen and your phone both rely on Wi-Fi.

Prices on the store are final and include VAT, and you can split the payment with Tabby. Send us your floor count, rooms and expected number of devices on WhatsApp and we will help you choose the model and quantity.

Browse all access points at Misbar →

FAQ

What is the best access point for a villa?

For most villas, the Grandstream GWN7660E with Wi-Fi 6 and 256 connected devices, one per floor. For an annex or a room with no cable, the GWN7660EM plugs into the wall socket and joins over Mesh.

Does an access point need a power socket next to it?

Not when it runs from a PoE switch, since the network cable carries power and data. The exception is the GWN7660EM, which mounts in the socket itself and does not take PoE.

Should I buy a Wi-Fi 6 or Wi-Fi 7 access point?

Wi-Fi 6 covers most homes and offices today. Wi-Fi 7 units such as the GWN7670E and AP371 are worth it if your newer devices support Wi-Fi 7 or your fibre line is faster than 1 Gbps, since both have a 2.5G port.

Grandstream or Huawei access points: what is the difference?

Grandstream includes a built-in controller for up to 50 units, a free GDMS Networking cloud, and a wider range of Mesh and in-wall models. Huawei eKit is managed from the HUAWEI eKit app, SNC cloud or a WAC controller, and suits companies already running Huawei switches.

Can an outdoor access point handle the Saudi summer?

The GWN7660ELR and Huawei AP771 are both rated to operate up to 60°C by their manufacturers, and the AP771 adds IP65 dust and water protection.

Which access point should you choose?

• Villa or small office: the GWN7660E, one per floor.
• Annex or room with no cable: the GWN7660EM.
• Hotel rooms or serviced apartments: the GWN7661E, or the AP160 for small rooms.
• Offices on a Huawei network: the AP362E.
• Busy hall, school or restaurant: the GWN7664E.
• Wi-Fi 7 with fast fibre: the GWN7670E or AP371.
• Courtyard, pool or car park: the GWN7660ELR or AP771.

Every sales call and support request passes through your phone system, so the wrong PBX keeps costing you long after purchase. This IP PBX buying guide covers the four questions that decide the right model for a Saudi business, then compares two series sold at Misbar: Yeastar P-Series and Grandstream UCM6300.

What an IP PBX does

An IP PBX runs your company's calls over the office network instead of telephone wiring. Each employee gets an extension on a desk IP phone, a mobile app or a computer, and the PBX routes calls between departments. Adding a new hire takes a setting, not a cabling job, and staff can answer the company number from their mobile.

IP PBX buying guide: four questions to answer first

1. How many users, today and in three years?

Count everyone who needs an extension, plus reception, the warehouse and the meeting room. Size for growth: replacing the PBX after a year costs more than buying extra capacity now.

2. How many concurrent calls?

Concurrent calls are the calls happening at the same moment. In most offices this sits well below the user count, since not everyone calls at once. Call centers need a figure close to their headcount.

3. Which lines will you connect?

• STC landlines: you need FXO ports.
• Mobile SIMs from STC, Mobily or Zain: you need a 4G port on the PBX or a separate GSM/4G gateway.
• A SIP trunk from your provider: it connects over the internet, with no extra ports.
• Existing analog phones you want to keep: you need FXS ports.

4. Does your team work outside the office?

With sales reps on the road or branches in Riyadh, Jeddah and Dammam, pick a PBX with mobile and desktop apps so each extension travels with its owner.

Yeastar and Grandstream models by the numbers

• Yeastar P550: 50 users and 25 concurrent calls, with up to 8 FXS, 8 FXO and 4 cellular ports depending on the modules installed.
• Yeastar P560: 100 users (expandable to 200) and 30 concurrent calls (expandable to 60), plus support for one E1 port.
• Yeastar P570: 300 users (expandable to 500) and 60 concurrent calls (expandable to 120).
• Grandstream UCM6301: 500 users and 75 concurrent calls, with 1 FXO and 1 FXS port.
• Grandstream UCM6302: 1,000 users and 150 concurrent calls, 2 FXO and 2 FXS ports, and video meetings for up to 30 participants.
• Grandstream UCM6304: 2,000 users and 300 concurrent calls, 4 FXO and 4 FXS ports, and video meetings for up to 60 participants.
• Grandstream UCM6308: 3,000 users and 450 concurrent calls, 8 FXO and 8 FXS ports, and video meetings for up to 80 participants.

Yeastar or Grandstream: which one fits?

Choose Grandstream UCM6300 for high user and call capacity in one unit, built-in analog line ports, and video meetings hosted on the PBX. The Wave app handles calls on mobile and desktop, and UCM RemoteConnect secures remote access.

Yeastar P-Series suits companies that want to add landline or 4G SIM modules only where needed. It offers Linkus apps for mobile, desktop and web, call center tools such as skill-based routing and a real-time wallboard, and CRM integrations with Zoho, Salesforce, HubSpot and Odoo. Some features depend on the subscription plan, so ask which plan covers them when you order.

Quick picks by company size

• Up to 50 employees: Yeastar P550, or Grandstream UCM6301 if you expect fast growth.
• 50 to 200 employees: Yeastar P560 or Grandstream UCM6302.
• Large companies, multiple branches or call centers: Yeastar P570, or Grandstream UCM6304 and UCM6308.

Buy Yeastar and Grandstream PBX systems from Misbar

Misbar sells the Yeastar P550, P560 and P570 and the Grandstream UCM6301, UCM6302, UCM6304 and UCM6308, plus the IP phones, PBX modules and gateways that complete the system. Pay with mada or Apple Pay, or split it into up to 12 monthly payments with tabby. Fitting out a whole office? Message us on WhatsApp for a quote on the PBX, phones and gateways.

FAQ

Do I need new phones with the PBX?

Not necessarily. The PBX works with desk IP phones and the mobile app, and FXS ports keep your analog handsets in use.

Can I connect an STC or Mobily SIM to the PBX?

Yes. The Yeastar P550 and P560 support up to 4 cellular ports through modules. With Grandstream, you connect the SIM through a 4G gateway linked to the PBX.

What is the difference between users and concurrent calls?

Users are the extensions registered on the PBX. Concurrent calls are the calls that can run at the same moment.